| Image | Item | MSRP | Price |
|
10 1/2" Tie Bar (Water pump to Alternator)
10 1/2" tie bar install between MK IV sea water pump and alternator, mounted on low mount bracket. Used to easily and equally tighten v-belts on sea water pump and alternator. Includes rod ends and lock nut.
Part #: 307
| $75.45 | $55.25 |
|
7" Oil Filter Mounting Bracket & Spacer
7" remote oil filter mounting bracket - mounts HP4 or HP6 remote oil filter head in horizontal position, to rear of engine head, on port side of engine. Includes 1/2 inch spacers.
Part #: 215
| $74.10 | $60.82 |
|
Alternator Bracket/SS Bushing
Alternator bracket with SS bushings - Mounts on lower port side of engine block. Places center line of alternator below center line of crankshaft, helping to lower center of gravity of engine. Includes stainless bushing. Fits large and small Delco, Prestolite and Mando style alternators.
Part #: 305
| $136.36 | $111.94 |
|
Aluminum Lift Ring Bracket & Spacers
Aluminum lift ring bracket with spacers - One bracket mounts on front port side of head and one bracket mounts on starboard rear of head. Allows engine to be lifted level. Includes 1/2" spacer. Two required per engine, sold as a set.
Part #: 310
| $163.00 | $135.00 |
|
Billet Idler Pulleys
All have replaceable bearings and are slotted for weight, cooling & appearance. Designed to replace fragile plastic pulleys on MerCruiser & other similar type applications, includes bearing. Four types are currently available. Can also be used for automotive applications.
#121 - 4.42" Grooved Poly-V Pulley (MerCruiser EFI Series)
#122 - 3.20" Grooved Poly-V pulley
#123 - 3.20" Smooth -for front or rear of V-Belt (used with MK V & VI seawater pumps.)
#124 -rear of poly-V Belt 3.20" Smooth for
Price for #121 is $48.37
Part #: 121, 122, 123 & 124
| $49.70 | $45.18 |
|
Billet Prop Shaft Cover
Prop shaft cover protects prop shafts from dirt and damage. Inside of cover is tapered to allow water and condensation to drain out. Prop shaft nut can be tightened by holding cover. Cover will not damage out drive housing if installed and drive put in gear.
#260 - Fits Bravo XR, XZ & large shaft outboards
#265 - Fits large shaft Speed Masters III A, IV, V & VI
Part #: 260,265
| $75.45 | $61.94 |
|
Dry Sump Pump/Alternator Bracket (Weaver Style)
Dry sump pump/alternator bracket - Combination Weaver style dry sump oil ump and low mount alternator bracket. mounts to lower front port side of engine block. Includes SS alternator busing.
Part #: 250
| $225.45 | $185.07 |
|
Front Lift Ring/Oil Filter Mt. Bracket & Spacers
Front lift ring/oil filter mounting bracket & spacers - mounts to front, port side, of engine. Serves as lift ring and front mounting bracket for #206 oil filter head. Oil filter mounts in vertical position and will clear exhaust pipe on staggered or tripple engine installations, can be mounted on top of MerCruiser power steering bracket.
Part #: 311
| $59.09 | $48.50 |
|
Fuel Filter Head and Adapter
Fuel filter head and adapter - has integral mounting bracket. Can be mounted in vertical or horizontal position. Uses MerCruiser type filters or Fram PCS5062M filter. Has 1/2" NPT threaded inlet and outlet. Same body as #206 & #207, difference is adapter. Can be used with bracket #311.
#400 - Has END entry/exit threaded holes.
#401 - Has SIDE entry/exit threaded holes.
Part #: 400,401
| $124.55 | $102.25 |
|
GM Power Steering Bracket w/ Spacers
GM power steering bracket with spacers - Allows mounting of GM style power steering pumps to front of starboard cylinder head. Includes 1" spacers.
Part #: 235
| $77.45 | $63.58 |
|
GM Power Steering Pump Housing Assembly
GM power steering pump housing assembly - Billet aluminum pump housing replaces stamped steel housing. Tapped 3/8 NPT fittings. Includes studs & spacers. Requires modification of existing pressure valve.
Part #: 231
| $212.98 | $170.38 |
|
HP 4 BBC Oil Filter w/Adapter
HP 4 remote oil filter head with filter adapter - Allows HP4 style oil filter to be remote mounted. 2 holes threaded 1/2 inch NPT for oil lines & 3 holes threaded 1/8 inich NPT for sending units. Includes filter adapter.
Part #: 205
| $123.15 | $101.10 |
|
HP 6 BBC Oil Filter w/Adapter
HP6 remote oil filter head with adapter allows HP6 style oil filters to be remote mounted. 2 holes threaded 3/4" NPT for oil lines and 3 holes threaded 1/8" NPT for sending units. Includes filter adapter.
Part #: 220
| $137.36 | $112.76 |
|
Mark 4 Sea Water Pump Spacer Bracket Unit
Mk 4 sea water pump spacer bracket - pivots MK IV sea water pump assembly out 1 inch away from oil pan. Allows use of large capacity oil pans.
Part #: 300
| $21.60 | $17.73 |
|
MCM Sea Water Pump End Cap Hard Coat Anodized
MCM sea water pump end cap - machined billet aluminum endcap for MerCruiser and Jabsco type sea water pumps. End cap is threaded 1"female NPT and hard coat anodized for corrosion resistance.
Part #: 245
| $83.65 | $68.66 |
|
Oil Filter Head & Adapter
Oil filter head & adapter has integral mounting bracket. Can be mounted in Vertical or Horizontal position. Uses Fram HP-4 type oil filters. Has 1/2 inch NPT threaded inlet and outlet. Same body as #400 & #401. Difference is adapter. Can be used with bracket #311.
Part #: 206 & 207
| $124.55 | $102.23 |
|
Spiral Fin Alternator Pulley
3.25" diameter with integral 5" diameter fan. Spiral fins & slots allow fan to pull cool air in from rear of alternator and cool voltage regulator.
#115 - fits Mercruiser/Mando Alternator (2 flats on shaft)
#116 - fits large Delco Alternator (straight shaft)
#117 - fits small Delco/Prestolite Alternator (1/8 Key way)
Part #: 115, 116, & 117
| $115.60 | $94.90 |
|
Vertical Rear Mount Oil Filter Bracket
Vertical rear mount oil filter bracket - mounts #207 oil filter head (not included) in vertical position with filter down on rear of port side head. Includes spacers.
Part #: 312
| $83.00 | $66.40 |